Here are the details of 2011 NTPC Placement Paper - II job in NTPC. This job or placement paper has been sourced from either company website or newspaper or other media and from students who appeared for this job. User is requested to verify the data before applying for the job.
Welcome to NTPC Placement Paper 2011. Here you will find NTPC Paper Pattern and Download questions of NTPC Placement Paper 2011 with Answers & Solutions.
2011 NTPC Placement Paper:-
1 An ice block submerged in the water, if the ice melts level of water (increase,decrease,remains same,none)
2 Simply supported beam with w point load at the middle, max. bending moment?(wl/4)
3 Simply supported beam with UDL ,max.deflection (wl4/384EI)
4 Cantilevel beam point load at tip,max.bending momemt comes at (end)
5 When bearing life L10 represents (bearings 10%survive,bearings 10% fails, none )
6 For welding high carbon steels which type of flame is used (oxidizing,carburizing,neutral,none)
7. Arrange the following cutting tools in decreasing order of machining hardness…Ceramics
8. When P1 and P2 are the loads acting on bearings with life L1 and L2 then L1/L2=?
9.Product simplification does not mean??
10 Which of the following process has the most scope in manufacturing?
CAD/CAM, CAM, CIM, All the above.
11. Concurrent engineering means?
(Manufacturing, designing, both,none)
12. Which manufacturing process yields higher output and increases worker productivity-
(process layout,line+process,functional layout)
13. 18-4-1 represents-, Tungsten-Cr-Vn
14 For which material is negative allowance provided-(Graphite,steel,bronze,cast iron)
15. What is the recrystallisation temperature of tin- (60,300,1000,none)
16. What is the purpose of borax in soldering-
17. Top gates are provided in which type of casting-(Shallow casting,simple,complex,none)
18. Which statement is true regarding simple gear trains-(i/p and o/p shafts r fixed, each shaft has 2 gears, i/p & o/p shafts r moving)
19. What is the purpose of normalizing- (Refining of grain structure)
20. As the grain size is decreased-(Hardness increases,corrosion resistance decreases,both)
21. Isothermal gas is filled in a vessel at a pressure P and temperature T then considering the compressible forces as the height increases pressure ??(linearly increases linearly decreases exponentially increase )
22. A bottle is filled with water and air and is tied to a string and is rotated in horizontal direction. Then in which direction will air bubble travel?
23. A empty bottle(in vaccum) filled with a gas at temp T and press P when the pressure of bottle reaches P temperature of the gas is _? (T,T/K,TK)
24. Bearing somerfield number _ with load on bearing?
25. Critical radius for a sphere is-(2k/h)
26. Critical radius exist for_ (spherical,cylindrical,both,slab)
27. Convectional resistance/internal resistance is called (biot number)
28. Nusselt no. is? (hl/k)
30 Which statement is true regarding critical path method? (i only one critical path exists for a network, more tha one with same duration,)
31. Shipment cost,inspection cost,storage cost comes under_ (carrying cost ,holding cost,)
32. Ischronous governers sensitivity is- (zero,infinite)
33. self energized brakes are-(friction moment acts in the direction of application of force,opposite to the direction of force, does not need a force to act ,)
34 The ratio of heat capacities for evaporator and condenser is_ (Zero,infinity)
35. when steam and air mixture with partial pressure 0.06 and 0.07 enters a condenser what is the condenser pressure? (0.06,0.07,0.53,0.03)
36. In pulverized burning of coal heat transfer from boiler to water occurs through_( predominant radiation, convection, conduction, conduction+convection)
37. Rankine cycle efficiency for same parameters increases mostly with_(reheat, regeneration, super heating )
38. Ericson cycle with all reversible processes assume_(carnot cycle,stirling,brayton
39. Air delivery tank at outlet of reciprocating compressor is provided for_ (provide constant pressure, avoid cavitation, )
40. High speed centrifugal pump has _?
(vanes faces in forward direction side,backward,radial vanes)
41. Thermal efficiency in decreasing order_?
(Otto cycle>dual cycle>diesel cycle)
42. When a 1000 K body comes in contact with atmosphere at 300K a loss of 9000 KJ heat is transferred. The net available energy transferred is_
43. When entropy of a system increases_?
(unavailable energy increases )
44. Rolling is a process widely used for_?
45. Tool nomenclature_?
46. In francis turbine movement of steam?
47. For low power consumption _?
(rake angle should be increased / decreased, nose angle increased/ decreased)
47. Continuous chips occur in_?
(High speeds,low speeds,both,none)
48. Primary forces in a reciprocating engine_?
(fully balanced, partially balanced, completely unbalanced, none)
49. In proximate analysis pyrogallol is used for analysis of which element_?
50. Sulphur content in fuel greatly affects_?
51. Heat transfer through radiation can be increased by_?
(decreasing emissivity and increases temperature of hot body)
52. which theory of failure clearly explains the failure in case of ductile material?
(Maximun shear stress theory or Guests or trescas theory)
53. When a material is subjected to continuous cycles which limit is being verified?
54. where is stress concentration maximum?
(notches, stress reducing throughcuts)
55. Power transmitted through a belt drive_?
56. According to Eulers theory crippling or buckling load is
(Wcr = Cπ2EI/l2)
57. During sensible heating, specific humidity_?
58. COP of a refrigerator is _?
(greater than 1 )
59. The maximum temperature in a refrigeration cycle is_?
(less than/greater than/equal to critical temperature)
60. The pressure at the throat of the nozzle_?
61. for a statically determinate set of forces for equilibrium_?
62. For a statically determinate set of forces-
(there r as many equations as the no. of unknowns)
63. 1-2-3 analysis is used for_?
(1.break even analysis, ??)
64. A problem on mean time of service something like a salesman has a rating of 120. considering 10% allowance time calculate the time required to serve 120???
65. A problem n determining time in a queue??
66. Energy equation for a laminar flow is _?
(Uniform and steady ,non uniform and unsteady)
67. Undercuts in welding occurs due to_?
( low welding current,high welding current)
68. Work holding equipment in shearing??
69. At the centre of a nozzle _?
( Mach no<1 >=1;=1)
NTPC, India's largest power company, was set up in 1975 to accelerate power development in India. It is emerging as an ‘Integrated Power Major’, with a significant presence in the entire value chain of power generation business.
NTPC ranked 317th in the ‘2009, Forbes Global 2000’ ranking of the World’s biggest companies. With a current generating capacity of 33,194 MW, NTPC has embarked on plans to become a 75,000 MW company by 2017.
Why NTPC - Why should i join NTPC:-
NTPC has well established talent management systems in place to ensure that the company delivers on its promise of providing exponential growth and challenge to all employees.
* Performance Management - NTPC has a standardised and formalised performance management system. A KPA based system is designed to assess functional, managerial and potential competence in an objective and transparent manner. The system is designed to accomplish the overall organisational vision and mission by linking individual performance to the company’s objectives and strike a balance between performance and competence to help individuals excel in their fields.
* Career Paths - A formal career path and development process exists in NTPC. All career paths have an underlying management structure. Promotions within each career path are aligned with the needs of the organisation. Succession criteria for leadership positions in each career path have been identified, which provide basis for job rotation. Anyone joining the organisation can choose to pursue a business, function or staff career path and will be put through specific training interventions and job rotation path towards becoming a business, function or staff head.
* Leadership Development - Potential employees are assessed for leadership competence and are groomed to occupy leadership positions in the company. We have a system that enables measurement of leadership effectiveness, gap identification against an identified set of leadership competence. Individual development plans are made based on the gaps identified to ensure that the process of development and growth is meaningful.
SCOPE Complex, Institutional Area, Lodhi Road,
New Delhi - 110003
EPABX BOARD NOS.: 91 11 24360100, 24387000, 24387001
FAX NO.: 91 11 24361018
(Disclaimer : This Job or placement paper has been sourced from various sources like print media, Job consultants, past candidates, our users and/ or Company website. The posted date above means the date on which the Job was posted on our site and not on the company site. Users are advised to check with the company for latest requirements before applying for the job. Our website will not be responsible for any loss to the company or the candidate. We have no relation with the company and are not responsible for the validity of this Job. We donot charge the company or candidate or any student anything. If the respective company has any issue with the data provided or they want this particular job or placement paper to be removed they can write into us at email@example.com)